Idaho ITD CDL General Knowledge Practice Test 9

  • Questions50
  • Correct to pass40
  • Passing score80%
  • Minimum age18 years

50 questions. Pick an answer to see if it is right and why; you need 40 correct answers to pass.

  1. 1. What are you looking for when you check the drive belts in the engine compartment?

    Show answer

    Answer C: That each belt is snug and free of cracks, frays or heavy wear

    A loose or cracked belt can break and stop the fan, the water pump or the alternator, which leads quickly to overheating or a dead electrical system.

  2. 2. What does the federal bridge formula do?

    Show answer

    Answer C: It reduces the weight allowed on a group of axles as those axles get closer together

    Axles bunched together concentrate the load on a short span of a bridge, so the formula lowers the allowable weight as the spacing shrinks.

  3. 3. Within total stopping distance, what exactly is perception distance?

    Show answer

    Answer D: The distance traveled from the moment your eyes see a hazard until your brain identifies it

    Perception distance covers only the time between seeing a hazard and recognizing it as a hazard, before any physical reaction begins.

  4. 4. What must be true of the trailer landing gear before you move off?

    Show answer

    Answer B: Fully raised, with the crank handle secured and no missing or damaged parts

    Landing gear left part way down can strike a railway crossing or a ramp, and a loose crank handle can swing out into a passing vehicle.

  5. 5. Within what distance should high beams be lowered at night?

    Show answer

    Answer D: Within about 500 feet of an oncoming vehicle and within about 500 feet of a vehicle you are following

    High beams blind other drivers at close range, so they are lowered at roughly the same distance whether the other vehicle is coming toward you or is ahead of you.

  6. 6. Where is a dunnage bag used and how does it work?

    Show answer

    Answer D: Between pieces of cargo inside a van, where it is inflated to take up the gap

    A dunnage bag is placed in the void between loads and inflated so the cargo is wedged and cannot move as the vehicle rolls and brakes.

  7. 7. You are making a right turn and cannot complete it without swinging into the oncoming lane. An oncoming car is approaching. What should you do?

    Show answer

    Answer A: Wait and let the oncoming vehicle pass before completing the turn, and do not back up

    The oncoming vehicle has the lane; backing up in traffic is dangerous, so hold your position and finish the turn once the way is clear.

  8. 8. An intermodal container is being carried on an ordinary flatbed rather than on a container chassis. What does that mean for securement?

    Show answer

    Answer B: It must be secured with tiedowns that meet the container securement requirements

    A container carried on a vehicle that is not fitted with integral locking devices has to be secured to the deck with tiedowns that satisfy the rules for containers.

  9. 9. How does overloading affect the way a vehicle drives?

    Show answer

    Answer C: It slows the vehicle on upgrades, makes stopping take longer and can overheat the brakes on downgrades

    Extra weight demands more from the engine and the brakes, so the vehicle climbs slowly and needs much more distance to stop.

  10. 10. You drive a 40 foot straight truck at 50 miles per hour in good conditions. What following distance does the rule of thumb call for?

    Show answer

    Answer A: 5 seconds

    One second for every 10 feet of vehicle length gives 4 seconds, and one extra second is added for speeds above 40 miles per hour.

  11. 11. During the walkaround inspection, where does the driver normally start and how does the check proceed?

    Show answer

    Answer C: At the left front of the vehicle, working around it in a set order that returns to the cab

    The walkaround follows the same route every time, starting at the left front and circling the vehicle, so that nothing is skipped when the driver is tired or rushed.

  12. 12. Which of these is a major cause of skids in heavy vehicles?

    Show answer

    Answer C: Over-braking, over-steering, over-acceleration or driving too fast for conditions

    Skids happen when the tires are asked for more grip than the road can give, which happens through braking, steering or accelerating too hard or simply too much speed.

  13. 13. Your truck has a backup alarm that sounds whenever reverse is selected. What may a driver rely on it for?

    Show answer

    Answer D: Very little; it warns some people but cannot show you what is behind the vehicle

    An alarm may not be heard over yard noise or by someone wearing hearing protection, so it never replaces looking at the path yourself.

  14. 14. Taking your eyes off the road for about five seconds at highway speed means traveling roughly how far unseen?

    Show answer

    Answer A: About the length of a football field

    At highway speed a five second glance away covers roughly 100 yards, which is far more road than any driver can afford to travel blind.

  15. 15. Which components on a typical engine are driven by belts that must be checked for wear and tension?

    Show answer

    Answer D: The alternator, the water pump and, on many vehicles, the air compressor

    Belts drive accessories such as the alternator, the water pump and the air compressor, so one failed belt can take out charging, cooling or air supply.

  16. 16. A commercial driver is convicted of two serious traffic violations within three years. What is the result?

    Show answer

    Answer D: Disqualification for 60 days

    Two serious traffic violations in a three year period bring a 60 day disqualification, and a third in the same period raises it to 120 days.

  17. 17. How does a driver measure following distance in seconds?

    Show answer

    Answer A: Wait for the vehicle ahead to pass a fixed roadside object, then count the seconds until the front of your vehicle reaches the same object

    Counting from the moment the vehicle ahead passes a landmark until you reach it turns a gap you cannot judge in feet into a number of seconds.

  18. 18. What should you check about the tire valve stems during the walkaround?

    Show answer

    Answer D: That the stems are not cut, cracked or leaking and the caps are in place

    A split stem or a missing cap lets air escape or lets dirt into the valve, and either one can flatten a tire between stops.

  19. 19. A commercial vehicle stops on the shoulder of an undivided two-lane road that carries traffic in both directions. Where do the warning devices go?

    Show answer

    Answer B: Within 10 feet of the vehicle, plus 100 feet to the front and 100 feet to the rear

    On a two-way road the devices must mark the vehicle itself and warn traffic approaching from each direction, and they must be in place within ten minutes.

  20. 20. On a two lane road carrying traffic in both directions, where do the three warning devices go?

    Show answer

    Answer C: About 10 feet from the vehicle on the traffic side, 100 feet behind and 100 feet ahead

    Traffic can approach from either direction, so one device goes close to the vehicle and one is placed about 100 feet away in each direction.

  21. 21. Below 40 mph, what following distance does the standard commercial rule of thumb call for?

    Show answer

    Answer C: One second for every 10 feet of vehicle length

    The base rule allows one second of space for each 10 feet of vehicle length while speed stays under 40 mph.

  22. 22. What is the purpose of the header board, or headache rack, that you inspect behind the cab?

    Show answer

    Answer A: It protects the driver from cargo that shifts forward during a hard stop

    In a hard stop the load keeps moving forward, and the header board is the barrier between that load and the back of the cab.

  23. 23. You are hauling a load of steel plate that is well within every weight limit but is stacked five feet high on a flatbed. What is the main concern?

    Show answer

    Answer A: The center of gravity is high, so the rig will roll more easily in a curve

    Legal weight does not make a load safe; height raises the center of gravity and it is height, not weight alone, that decides how readily the vehicle rolls over.

  24. 24. What is the correct way to make a normal stop?

    Show answer

    Answer A: Push the brake pedal down gradually and bring the vehicle to a smooth stop

    Steady, progressive pedal pressure keeps the vehicle stable and lets the driver behind you react to a predictable slowdown.

  25. 25. What is the best practice when fog is thick enough to hide the road ahead?

    Show answer

    Answer B: Slow down before entering the fog, and if visibility is too poor, pull off into a rest area or truck stop until it improves

    The safest choice in heavy fog is not to be driving in it, and if you are already in it your speed has to come down before your visibility does.

  26. 26. Why must exhaust components be checked for contact with other parts of the vehicle?

    Show answer

    Answer B: Hot exhaust parts touching fuel lines, tires or wiring can start a fire

    Exhaust pipes run hot enough to ignite fuel and melt insulation, so they must be kept clear of the fuel system, the tires and the electrical harness.

  27. 27. Which winter preparation matters most for keeping the road in view?

    Show answer

    Answer D: Working wipers, washer fluid and a working defroster

    Slush and road spray coat the windshield within minutes in winter, so wipers, washer fluid and the defroster are what keep any view at all.

  28. 28. Cargo securement must be strong enough to hold the load under which conditions?

    Show answer

    Answer A: Hard braking, hard acceleration and hard turning, as well as the bouncing of the road

    The securement standard is written around the forces of a hard stop, a hard start, a hard turn and vertical movement on a rough surface, all of which occur in ordinary driving.

  29. 29. What makes a brake hose or air line a defect during the walkaround?

    Show answer

    Answer D: It is cracked, worn, kinked, or rubbing against another part

    A chafed or cracked line can burst under pressure and take the braking on that circuit with it, so damage and rubbing points must be corrected.

  30. 30. For an unblocked article longer than 10 feet, the minimum is two tiedowns plus how many more?

    Show answer

    Answer B: One more for every additional 10 feet of length or any part of 10 feet

    Past the first 10 feet, one more tiedown is added for each additional 10 feet of length or any fraction of that distance.

  31. 31. Apart from the legal duty, what is the main practical reason for a thorough pre-trip inspection?

    Show answer

    Answer A: It finds problems that could cause a breakdown or a crash before the vehicle is on the road

    A defect found in the yard is an inconvenience, while the same defect found at highway speed can be a crash, so the inspection is where problems are cheapest to fix.

  32. 32. Under federal rules, which commercial vehicles must stop at every railroad crossing before proceeding?

    Show answer

    Answer D: Passenger buses and placarded hazardous materials vehicles

    Buses carrying passengers and vehicles required to display hazardous materials placards must stop at crossings, while other commercial vehicles slow and check.

  33. 33. What condition should the fifth wheel be in before you back under a trailer?

    Show answer

    Answer C: Jaws open, plate greased, and the fifth wheel tilted down toward the rear

    The jaws have to be open to take the kingpin, the plate must be lubricated to prevent hard steering, and the fifth wheel is tilted down at the rear so the trailer apron can ride up onto it.

  34. 34. The car in the next lane still has snow covering most of its windows. What should you assume?

    Show answer

    Answer C: That driver cannot see you and may move into your lane

    A driver whose view is blocked cannot see the vehicles around, so you should assume you are invisible and stay out of that vehicle path.

  35. 35. You are backing a tractor-trailer in a straight line and the trailer starts to drift to the left. What is the standard correction?

    Show answer

    Answer D: Turn the top of the steering wheel a little to the left, toward the drift

    Small corrections made in the direction the trailer is drifting bring it back into line; large or opposite movements make the drift worse.

  36. 36. During the walkaround you find the reflective conspicuity tape along the trailer caked with road grime. What should you do?

    Show answer

    Answer B: Clean it, because dirty reflective material cannot make the trailer visible at night

    Reflective sheeting only works if light can reach it and bounce back, so a dirty strip leaves the trailer effectively unmarked to approaching traffic.

  37. 37. Under federal rules, what happens to a commercial driver found with any detectable amount of alcohol while operating a commercial vehicle?

    Show answer

    Answer D: The driver is placed out of service for 24 hours

    Any measurable alcohol takes a commercial driver off the road for 24 hours, and a concentration of 0.04 percent or more brings a disqualification.

  38. 38. How does the working load limit of a tiedown relate to the force that would break it?

    Show answer

    Answer B: The working load limit is a fraction of the breaking strength and is the figure you use

    The working load limit is set well below the point at which the device would fail, and securement is always calculated from the working load limit, never from breaking strength.

  39. 39. During a right turn in a tractor-trailer, what are you looking for in the right hand mirror?

    Show answer

    Answer B: Whether the trailer will clear the curb and whether anything has moved alongside you

    The right mirror is what tells you how close the trailer wheels are running to the curb and whether a vehicle or a cyclist has slipped into the space on your right.

  40. 40. The paperwork shows a weight, but the load looks heavier than you expected. What should you do?

    Show answer

    Answer C: Weigh the vehicle, since you are the one answerable for driving it overweight

    The driver is the one who can be cited for an overweight vehicle, so a doubtful weight is settled on a scale before the trip continues.

  41. 41. Where should a trailer be dropped, and what else does the driver do before pulling out from under it?

    Show answer

    Answer C: On solid level ground, with the trailer wheels chocked if it may roll

    A dropped trailer must sit on ground that will carry the landing gear without sinking, and chocks stop it rolling once the tractor and its air supply are gone.

  42. 42. A commercial vehicle stops on the shoulder of a one-way or divided highway. Where do the three warning devices go?

    Show answer

    Answer A: At 10 feet, 100 feet, and 200 feet back toward approaching traffic

    Traffic arrives from one direction only, so all three devices are set back toward it at 10, 100, and 200 feet, and they must be out within ten minutes.

  43. 43. Why does a heavy vehicle need a much larger gap than a car in order to cross or enter traffic?

    Show answer

    Answer C: Because it accelerates slowly and needs far more road and time to clear the intersection

    Slow acceleration combined with the length of the vehicle means a gap that would feel comfortable in a car is nowhere near enough.

  44. 44. What blood alcohol concentration disqualifies the holder of a commercial driver license who is operating a commercial vehicle?

    Show answer

    Answer D: 0.04 or higher

    Commercial drivers are held to 0.04, half the limit that applies to a driver of a passenger car in the same state.

  45. 45. A tire blows out at highway speed. What should the driver do first?

    Show answer

    Answer C: Hold the steering wheel firmly, stay off the brake and let the vehicle slow down

    Braking while a tire is gone can pull the vehicle out of line, so the driver keeps it straight and lets speed fall before easing off the road.

  46. 46. What should be done before a night trip to get the most from your headlights?

    Show answer

    Answer C: Clean the windshield, the mirrors and the lights

    Dirt on glass and lenses cuts both the light you throw down the road and the light that reaches your eyes, so cleaning is the cheapest night safety measure there is.

  47. 47. How should a commercial driver treat the speed posted for a curve?

    Show answer

    Answer B: As a limit set for cars in good conditions, so a heavy or tall load calls for a lower speed

    Posted curve speeds are based on passenger vehicles in good conditions, and a tall or heavy load can roll over well below that speed.

  48. 48. You are moving an oversized load under a permit that requires a pilot vehicle. What is the pilot vehicle there to do?

    Show answer

    Answer B: Warn other traffic and check the route ahead for clearances and hazards

    Escort or pilot vehicles warn approaching traffic and scout the route for low bridges, narrow spots and other hazards that a wide or long load cannot pass.

  49. 49. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?

    Show answer

    Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit

    Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.

  50. 50. A car that passed you on the right slows and stays alongside your trailer. What is the best response?

    Show answer

    Answer D: Ease off the accelerator so the car can move clear

    A vehicle sitting beside a trailer is in a blind area and has nowhere to go if you need the lane, so the safest fix is to let it get ahead or behind.