Idaho ITD CDL General Knowledge Practice Test 4
Test 4 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Idaho test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. Which components on a typical engine are driven by belts that must be checked for wear and tension?
Show answer
Answer D: The alternator, the water pump and, on many vehicles, the air compressor
Belts drive accessories such as the alternator, the water pump and the air compressor, so one failed belt can take out charging, cooling or air supply.
-
2. How often may an Idaho seasonal commercial driver's license be obtained?
Show answer
Answer D: Twice in a lifetime
Idaho's seasonal CDL for farm-related service industries is valid for 180 days in a 12-month period and may be obtained only twice in a lifetime.
-
3. How much sleep does a typical adult driver need each day to stay properly alert?
Show answer
Answer D: Seven to eight hours
Most adults need seven to eight hours of sleep in every 24 hours, and a driver who regularly gets less builds up a debt that shows up behind the wheel.
-
4. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?
Show answer
Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit
Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.
-
5. What condition should the fifth wheel be in before you back under a trailer?
Show answer
Answer C: Jaws open, plate greased, and the fifth wheel tilted down toward the rear
The jaws have to be open to take the kingpin, the plate must be lubricated to prevent hard steering, and the fifth wheel is tilted down at the rear so the trailer apron can ride up onto it.
-
6. What happens to braking distance when speed is doubled?
Show answer
Answer C: It becomes about four times longer
Braking distance grows with the square of speed, so doubling the speed multiplies both the braking distance and the force of an impact by about four.
-
7. During the vehicle overview, what should the driver look for on the ground under the vehicle?
Show answer
Answer B: Fresh puddles of oil, coolant, grease or fuel
New stains on the ground are the earliest sign of a leak, so the overview includes a look underneath before anything is opened or started.
-
8. How does a driver keep a vehicle with a manual transmission from rolling back when starting on an upgrade?
Show answer
Answer D: Partly engage the clutch before the right foot leaves the brake, or hold the vehicle with the parking brake until the engine pulls
Something has to hold the vehicle during the instant the foot moves from the brake to the accelerator, and that is either the clutch at its engagement point or the parking brake.
-
9. What does the tachometer on the dashboard of a heavy truck show?
Show answer
Answer D: How fast the engine is turning, in revolutions per minute
The tachometer reads engine speed in rpm, which is what a driver uses to judge shift points in a vehicle with a manual transmission.
-
10. What is wrong with resting your foot on the clutch pedal between shifts?
Show answer
Answer B: It slowly wears the clutch out, because the pressure plate is never fully engaged
Any weight on the pedal partly disengages the clutch, so it slips and wears; the foot belongs off the pedal once the shift is finished.
-
11. The coolant temperature gauge climbs above its normal range on a long grade. What is the correct response?
Show answer
Answer C: Stop when it is safe to do so and find the cause before going on
Rising coolant temperature signals a fault such as a lost belt, a leak or a blocked radiator, and continuing can turn a repair into a destroyed engine.
-
12. Besides slowing down, which technique most reduces the risk of a skid on a snow covered road?
Show answer
Answer B: Make every steering, braking and speed change gradual
Traction is limited on snow, and sudden inputs demand more grip than the surface can supply, so smoothness is what keeps the tires attached to the road.
-
13. On a wet road, a commercial driver should reduce speed by roughly how much?
Show answer
Answer C: By about one third
Cutting speed by roughly a third, for example from 55 to about 35 mph, restores a margin for the traction lost on a wet surface.
-
14. What happens when too much of the load sits over the steering axle?
Show answer
Answer D: The vehicle becomes hard to steer and the axle and its tires can be damaged
Weight beyond the front axle rating makes the steering heavy and can overload the axle and the tires carrying it.
-
15. You are on a freeway and see brake lights come on in several vehicles far ahead of you. What should you do?
Show answer
Answer A: Ease off the accelerator and get ready to slow down
Brake lights well ahead are an early warning that traffic is slowing, and acting on them gives a heavy vehicle the room it needs.
-
16. Does the federal texting ban apply to a company dispatching device mounted in the cab?
Show answer
Answer B: Yes, entering or reading text on it while driving is banned
The rule is written around the act of reading or entering text on any electronic device, not around who owns the device.
-
17. What happens to braking performance if oil or grease reaches a brake lining?
Show answer
Answer B: That brake loses much of its effect and the vehicle can pull to one side
A contaminated lining cannot grip the drum, so that wheel contributes little braking and the vehicle pulls toward the side that is still working.
-
18. What does the suspension system weight rating tell the driver?
Show answer
Answer A: The maximum weight that the manufacturer says the suspension can carry
Like tires and axles, suspensions have a manufacturer capacity, and loading beyond it can damage springs and air bags.
-
19. Why must exhaust components be checked for contact with other parts of the vehicle?
Show answer
Answer B: Hot exhaust parts touching fuel lines, tires or wiring can start a fire
Exhaust pipes run hot enough to ignite fuel and melt insulation, so they must be kept clear of the fuel system, the tires and the electrical harness.
-
20. Which parts of total stopping distance can a driver shorten simply by staying alert and looking far ahead?
Show answer
Answer B: Perception distance and reaction distance
Alertness shortens the time spent recognizing a hazard and moving your foot to the pedal; braking distance depends on speed, weight, brakes and the road surface.
-
21. An empty van trailer cleared a low overpass on the way in, but on the way back it is loaded. Which statement is true?
Show answer
Answer C: An empty van rides higher than a loaded one, so it needs more clearance than when loaded
Springs compress under load, so an empty trailer is taller; the unloaded trip is the one that can catch a low overhead.
-
22. In dense city traffic you cannot see 12 seconds ahead because other vehicles block the view. What is the best response?
Show answer
Answer A: Slow down and open up more space in front of you
When you cannot see far enough ahead, extra following distance buys back the reaction time that the blocked view has taken away.
-
23. An intermodal container is being carried on an ordinary flatbed rather than on a container chassis. What does that mean for securement?
Show answer
Answer B: It must be secured with tiedowns that meet the container securement requirements
A container carried on a vehicle that is not fitted with integral locking devices has to be secured to the deck with tiedowns that satisfy the rules for containers.
-
24. You are making a right turn and cannot complete it without swinging into the oncoming lane. An oncoming car is approaching. What should you do?
Show answer
Answer A: Wait and let the oncoming vehicle pass before completing the turn, and do not back up
The oncoming vehicle has the lane; backing up in traffic is dangerous, so hold your position and finish the turn once the way is clear.
-
25. You are hauling an open box of loose gravel. What does that load require?
Show answer
Answer A: A cover, so that material cannot blow off or spill onto the road
Loose material that can be blown or spilled has to be covered so it does not come out of the body and strike traffic behind.
-
26. Which wheel or rim condition must be treated as a defect during the walkaround?
Show answer
Answer C: Cracks, illegal welded repairs, or missing and loose lug nuts
Cracked or welded rims and missing or loose fasteners can let a wheel separate from the vehicle and must be corrected before driving.
-
27. What is the driver looking for when the exhaust system is inspected?
Show answer
Answer B: Loose, broken or missing pipes, brackets or clamps, and signs that exhaust is leaking
A loose or leaking exhaust system can send carbon monoxide into the cab and can put hot gas against parts that will burn.
-
28. Dry bulk tanks call for extra caution mainly because of what?
Show answer
Answer C: A high center of gravity combined with a load that can shift
Dry bulk loads ride high and can move inside the tank, which makes the vehicle easier to tip in a curve.
-
29. Around a tractor-trailer, where are the blind areas that other drivers most often sit in unseen?
Show answer
Answer A: Along the right side and directly behind the trailer
The blind areas to the right of the cab and behind the trailer are the largest, which is why other drivers should never linger there.
-
30. Which combination of warning devices meets the requirement for a stopped commercial vehicle?
Show answer
Answer A: Three reflective triangles, or six fusees, or three liquid burning flares
A vehicle may carry three bidirectional reflective triangles, six fusees or three liquid burning flares as its warning devices.
-
31. A dock crew loads and straps the freight. Who is responsible for the load being legal and secure on the road?
Show answer
Answer D: The driver
Even when someone else loads and secures the freight, the driver must inspect it and remains responsible for it while driving.
-
32. Where is the yellow antilock brake malfunction lamp on a trailer, and what does it mean if it stays lit?
Show answer
Answer D: On the left side, at the front or rear corner, and it means the antilock function may not be working
Trailers carry the yellow lamp on the left side, and a lamp that stays on after the bulb check means the antilock function may be lost even though the normal brakes still work.
-
33. You have chosen 40 miles per hour as your safe speed for a downgrade. How should the brakes be used?
Show answer
Answer A: Brake firmly to about 35, release, and repeat at 40
Proper technique is firm application to about 5 miles per hour below the safe speed, then full release so the brakes cool before the next application.
-
34. What is the driver responsible for when a load is covered with a tarp?
Show answer
Answer C: Fastening it so it cannot flap free, block a mirror, or come off in the wind
A tarp that works loose can tear away, block the driver view or the view of others, and become a hazard for the traffic behind.
-
35. You are strapping down a load with sharp metal edges on a flatbed. What should you use?
Show answer
Answer D: Edge protection between the strap and the sharp edges so the tiedown is not cut
Sharp edges cut or wear through a strap under tension, so edge protectors are required wherever a tiedown could be damaged.
-
36. You are pulling away from the curb after a delivery. Why is a mirror check needed first?
Show answer
Answer B: A cyclist or a vehicle may be coming up alongside you
Traffic and cyclists can arrive alongside a parked vehicle at any moment, so the mirrors must be checked immediately before pulling out.
-
37. A strap runs from an anchor point on one side of the trailer, over the load, and down to an anchor point on the opposite side. How much of its working load limit counts toward the total required?
Show answer
Answer C: All of it
A tiedown that is anchored on one side, passes over or around the cargo and is anchored on the other side counts its full working load limit toward the aggregate figure.
-
38. Cargo securement must be strong enough to hold the load under which conditions?
Show answer
Answer A: Hard braking, hard acceleration and hard turning, as well as the bouncing of the road
The securement standard is written around the forces of a hard stop, a hard start, a hard turn and vertical movement on a rough surface, all of which occur in ordinary driving.
-
39. You hear air escaping from a trailer tire during the pre-trip. What should you do?
Show answer
Answer C: Have it repaired or replaced before the vehicle is driven
An audible leak means the tire is failing now, and federal rules do not allow a vehicle to be operated on a flat or leaking tire.
-
40. Which road users are hardest to see at night?
Show answer
Answer C: Pedestrians and cyclists in dark clothing
People on foot or on a bicycle carry no lights of their own in many cases, so they appear only when the headlights reach them.
-
41. Your windshield washer reservoir is empty and rain and road spray are expected. What should you do?
Show answer
Answer D: Fill it before the trip, because you need the washers to keep the windshield clear
Wipers alone smear the film of oil and grit thrown up by traffic, so the washers are part of keeping a usable view of the road.
-
42. What tells a driver when to shift up in a vehicle with a manual transmission?
Show answer
Answer C: Engine speed in rpm together with road speed
Shift points are judged from engine rpm and road speed, using the operating range the manufacturer specifies for that engine.
-
43. At 55 mph, about how far does a vehicle travel during a typical 3/4 second perception time plus 3/4 second reaction time, before the brakes even begin to work?
Show answer
Answer C: About 120 feet
Each 3/4 second at 55 mph covers about 60 feet, so perception and reaction together use up roughly 120 feet before braking starts.
-
44. You are stopped in traffic on a steep upgrade behind another truck. How much space should you leave in front?
Show answer
Answer A: Enough that you can pull away without rolling back into the vehicle behind you
Room ahead lets you get moving smoothly on a grade instead of having to hold the vehicle perfectly still or roll back toward the traffic behind.
-
45. A commercial vehicle stops on the shoulder of a one-way or divided highway. Where do the three warning devices go?
Show answer
Answer A: At 10 feet, 100 feet, and 200 feet back toward approaching traffic
Traffic arrives from one direction only, so all three devices are set back toward it at 10, 100, and 200 feet, and they must be out within ten minutes.
-
46. Why should the radio, the fan and other noisy equipment be switched off during a required stop at a railroad crossing?
Show answer
Answer C: So that an approaching train can be heard
The rules require the driver to look and listen along the track, and on a double track crossing a passing train can hide a second one, so hearing matters as much as seeing.
-
47. How soon must warning devices be placed after a commercial vehicle stops on the traveled part or the shoulder of a highway?
Show answer
Answer D: As soon as possible and in any case within 10 minutes
The hazard warning flashers go on immediately and the warning devices must be in place as soon as possible, never later than 10 minutes after stopping.
-
48. You need to pull off onto the shoulder because of a problem with the load. How should you communicate that to other drivers?
Show answer
Answer D: Signal the move, then switch on the four-way flashers once stopped
Other drivers need a signal before you leave the lane and a clear warning once the vehicle is stopped near the traffic lanes.
-
49. Besides being at least 18 years old, what does Idaho require of an applicant for a commercial driver's license?
Show answer
Answer A: One year of licensed driving experience
ITD requires CDL applicants to be at least 18 and to hold or qualify for an Idaho Class D license, and Idaho Code also requires one year of licensed driving experience.
-
50. How much free play in the steering wheel is enough to make a vehicle hard to steer and should be reported?
Show answer
Answer B: More than 10 degrees, roughly 2 inches of movement at the rim of a 20 inch wheel
Excess play means steering input is lost before the wheels respond, and more than about 10 degrees is treated as a defect.