Idaho ITD CDL General Knowledge Practice Test 1
Test 1 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Idaho test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. How long must an Idaho Commercial Learner's Permit be held before the CDL skills test may be taken?
Show answer
Answer C: At least 14 days
Idaho follows the federal rule that a Commercial Learner's Permit must be held for at least 14 days before the applicant may take the skills test.
-
2. Why should the radiator cap never be removed while the engine is hot?
Show answer
Answer A: The cooling system is under pressure and scalding coolant can be sprayed out
A hot cooling system holds pressurized coolant above its normal boiling point, so releasing the cap can throw boiling liquid and steam at whoever is holding it.
-
3. What do you check about the fire extinguisher during the pre-trip?
Show answer
Answer C: That it is securely mounted, charged and that you know how to operate it
An extinguisher must be held in its bracket, show a charged gauge and be understood by the driver, because a fire leaves no time to learn.
-
4. Why should a driver avoid shifting gears in the middle of a turn at an intersection?
Show answer
Answer D: Shifting during the turn takes a hand off the wheel and can cost you control
Pick the gear before you begin turning; shifting in the turn removes a hand from the wheel and can interrupt power just when you need steady control.
-
5. As a long vehicle goes around a corner, how do the rear wheels travel compared with the front wheels?
Show answer
Answer A: They follow a tighter path, closer to the inside of the turn
The rear wheels off-track toward the inside of the turn, and the longer the vehicle the bigger the difference, which is why the front must swing wide enough to keep the rear off the curb.
-
6. Why is it harder to judge speed and distance at night?
Show answer
Answer C: You see much less detail and have fewer reference points
Darkness removes the visual references that the brain uses to estimate distance and closing speed, so drivers routinely misjudge both.
-
7. Which vehicle is most likely to be pushed around by a strong crosswind?
Show answer
Answer B: An empty van trailer
A large flat side with very little weight behind it gives the wind the most surface and the least resistance, which is the empty van trailer.
-
8. How many questions are on the Idaho CDL hazardous materials knowledge test, and how many must be correct?
Show answer
Answer B: 30 questions, with 24 correct required
Idaho publishes the hazardous materials knowledge test as 30 questions with a minimum of 24 correct answers.
-
9. A tire blows out at highway speed. What should the driver do first?
Show answer
Answer C: Hold the steering wheel firmly, stay off the brake and let the vehicle slow down
Braking while a tire is gone can pull the vehicle out of line, so the driver keeps it straight and lets speed fall before easing off the road.
-
10. At a rest area you find that the load has shifted although the straps still feel tight. What should you do?
Show answer
Answer C: Correct the load before driving on, since a shifted load is no longer secure
Movement means the securement has already failed once, and a load that has shifted can shift again, so it is put right before the vehicle moves.
-
11. Why should a long vehicle never swing out to the left before starting a right turn?
Show answer
Answer D: Another driver may read it as a left turn or pass on your right
Swinging left opens a gap on your right that a car will move into, and it also sends a false message about which way you are going.
-
12. What should the ammeter or voltmeter show once the engine is running?
Show answer
Answer D: A reading in the normal charging range
With the engine running, the alternator should be charging; a discharge reading or an abnormal charge level means an electrical fault.
-
13. An unblocked article is 8 feet long and weighs 900 pounds. How many tiedowns does the federal rule require?
Show answer
Answer B: Two
Only an article that is 5 feet or shorter and 1,100 pounds or lighter can be held with a single tiedown; anything longer than 5 feet needs at least two whatever it weighs.
-
14. What are you looking for when you check the hubs and wheel seals during the walkaround?
Show answer
Answer B: Leaking oil or grease, which can also contaminate the brake linings
A leaking hub seal starves the bearing of lubricant and the escaping oil or grease can soak the brake linings and cut braking power.
-
15. Why does the manual insist on a firm grip with both hands on opposite sides of the steering wheel?
Show answer
Answer A: A hard bump can pull the wheel out of a loose grip
Hitting a curb or a deep pothole can jerk the wheel violently, and only a firm two-handed grip keeps the vehicle under control when that happens.
-
16. A 60 foot combination traveling above 40 mph should hold how many seconds of following distance?
Show answer
Answer D: Seven seconds
Six seconds cover the 60 feet of vehicle length, and one extra second is added because the speed is above 40 mph.
-
17. You are pulling away from a curb in a 65 foot combination. Besides traffic, what must you watch?
Show answer
Answer B: The trailer wheels, which stay close to the curb and can strike it or an object on it
Because of off-tracking, the rear wheels follow a tighter path than the front, so they stay near the curb while the cab is already out in the lane.
-
18. What does the gross combination weight rating cover?
Show answer
Answer B: The maximum loaded weight of the power unit together with the trailer or trailers it tows
The combination rating takes in the power unit and everything behind it, loaded, as specified by the manufacturer.
-
19. What is the purpose of the torque rods or radius rods you check on the suspension?
Show answer
Answer A: They hold the axle in alignment with the frame under braking and acceleration
Torque rods resist the twisting and fore and aft forces on the axle, so a cracked or missing rod lets the axle move out of alignment.
-
20. An automatic transmission is left in its normal drive position as the vehicle rolls down a long grade. What does it tend to do?
Show answer
Answer A: Shift up as road speed rises, so engine braking falls away
An automatic left in drive keeps upshifting as speed builds, which is the opposite of what you want on a grade; that is why the driver must select a low range.
-
21. How do you avoid the sharp lurch that comes at the very end of a stop in a heavy vehicle?
Show answer
Answer A: Ease off the brake pressure just before the vehicle actually comes to rest
A smooth stop is finished by reducing pedal pressure as the vehicle settles, so the suspension does not rock the cab and the load forward.
-
22. On a scale, your loaded truck is well under the gross weight limit, but one axle is above the limit for that axle. What does this mean?
Show answer
Answer D: The vehicle is overloaded and the load must be shifted or reduced before you drive on
Each axle and axle group has its own limit and each must be respected; being under the gross limit does not excuse an overloaded axle.
-
23. You are unsure whether your vehicle will fit through a narrow gate. What should you do?
Show answer
Answer A: Stop, get out and look, and take another route if the space is not clearly enough
Clearance is never guessed at from the seat; you look at it on foot and go round rather than trying a gap that may be too tight.
-
24. What is the coupling device weight rating on a vehicle?
Show answer
Answer A: The most weight that the coupling on the vehicle is rated to pull
The coupling device rating is a limit on how much weight the coupling may tow, and it is one of the ratings that has to be respected when a combination is loaded.
-
25. Which items belong to the in-cab part of the inspection?
Show answer
Answer D: Gauges, controls, mirrors, windshield, wipers, horn, heater and defroster
The in-cab step checks the instruments and controls the driver depends on, along with mirrors, glass, wipers, horn and the heater and defroster.
-
26. Your brakes have failed on a downgrade and there is no escape ramp in sight. What is the best choice?
Show answer
Answer A: Steer into an open field or onto a side road that flattens out or climbs uphill
A flat or uphill escape route uses gravity and rolling resistance to stop the vehicle; take it as soon as you see it, because the longer you wait the faster you go.
-
27. What is the main purpose of a retarder fitted to a heavy vehicle?
Show answer
Answer B: To help slow the vehicle and reduce the need to use the service brakes
Exhaust, engine, hydraulic and electric retarders all slow the vehicle so the brakes stay cool and wear less, especially on grades.
-
28. What must the motor carrier do about a defect listed on a driver vehicle inspection report?
Show answer
Answer D: Repair it, or certify that repair is not needed, before the vehicle is dispatched again
A reported defect must be corrected, or certified as not needing correction, and that certification is what the next driver reads before taking the vehicle.
-
29. Under the federal hours of service rules, how long may a property-carrying driver drive after 10 consecutive hours off duty?
Show answer
Answer D: Up to 11 hours, and only within a 14 hour window that starts when the driver comes on duty
The federal limit is 11 hours of driving after 10 consecutive hours off duty, and all of that driving has to fall inside a 14 hour window.
-
30. You pick up a sealed trailer at a shipper. What should you check before leaving the dock?
Show answer
Answer B: That the seal number matches the paperwork and that the doors are properly closed
You cannot look at a sealed load, but you can confirm that the seal is intact, that its number matches the documents and that the doors are secure.
-
31. During the walkaround you notice one tire on an axle is a radial and the tire next to it is bias-ply. What should you do?
Show answer
Answer B: Treat it as a defect, because radial and bias-ply tires must not be mixed on the same axle
Radial and bias-ply tires flex and grip differently, so mixing them on one axle makes the vehicle handle unpredictably and is not allowed.
-
32. How do objects appear in a convex mirror compared with a flat mirror?
Show answer
Answer B: Smaller and farther away than they really are, while a wider area is shown
A convex mirror shows a wider field but shrinks everything in it, so the driver must remember that vehicles are closer than they look.
-
33. A brake light lens is cracked and the lamp still lights. How should that be treated?
Show answer
Answer B: As a defect, because water can enter and the lamp can dim or fail
A cracked lens lets in water and dirt, which corrodes the socket and dulls the lamp, so it is reported before it becomes a dead brake light.
-
34. Two vehicles of exactly the same length make a right turn, one gently and one very tightly. What is the effect on off-tracking?
Show answer
Answer A: Turning more sharply increases off-tracking, so the tight turn needs more room
Off-tracking depends on both the length of the vehicle and the sharpness of the turn; a tighter corner brings the rear wheels further inside the path of the front wheels.
-
35. Your brakes have failed and you decide to use the parking brake to slow down. Why should you hold the release button or lever while doing so?
Show answer
Answer D: So you can release the brake at once if the wheels lock and the vehicle starts to skid
The parking brake can lock the wheels; keeping your hand on the release lets you let go the moment a skid starts and regain control.
-
36. During a right turn in a tractor-trailer, what are you looking for in the right hand mirror?
Show answer
Answer B: Whether the trailer will clear the curb and whether anything has moved alongside you
The right mirror is what tells you how close the trailer wheels are running to the curb and whether a vehicle or a cyclist has slipped into the space on your right.
-
37. How long must a motor carrier keep a driver vehicle inspection report and the certification of repairs?
Show answer
Answer B: Three months
The original report and the certifications attached to it are kept on file for three months from the date the report was prepared.
-
38. A driver behind you wants to pass and you can see that the road ahead is clear. What should you do?
Show answer
Answer B: Do not signal the other driver to pass; let that driver decide when it is safe
Directing other drivers can cause a crash if you misjudge the gap, so leave the decision to the driver who is passing.
-
39. The brake pedal goes to the floor in a vehicle with hydraulic brakes. What can you do to build some braking pressure?
Show answer
Answer B: Pump the brake pedal rapidly, which may bring back enough pressure to slow the vehicle
Pumping can restore some hydraulic pressure; along with downshifting and the parking brake it is one of the ways to stop when the pedal fails.
-
40. Why must cargo also be held down against vertical movement and not only against sliding?
Show answer
Answer D: Because a load that bounces can jump the blocking and slacken its own tiedowns
Rough road makes an unrestrained article lift; every bounce lets it move a little and works the tiedowns loose until nothing is holding it.
-
41. After starting the engine, how quickly should the oil pressure gauge come up to its normal range?
Show answer
Answer B: Within a few seconds
Oil pressure should build within seconds of starting; if it stays low, the engine is not being lubricated and should be shut down.
-
42. Your vehicle begins to hydroplane on a wet road. What should you do?
Show answer
Answer B: Release the accelerator and push in the clutch so the wheels can turn freely and regain grip
Hydroplaning tires are riding on water; slowing without braking lets them settle back onto the road and grip again.
-
43. A straight truck has a long body behind the rear axle. What happens to that overhang in a sharp left turn?
Show answer
Answer D: It swings out to the right and can strike a vehicle or an object on that side
Body that hangs behind the rear axle swings the opposite way to the turn, so the tail of the truck sweeps out into the next lane or over the curb.
-
44. You have a part load that fills only a third of a long trailer. How should it be placed?
Show answer
Answer C: Spread out and centerd side to side, so the weight sits over the axles
A part load is spread over as much of the floor as possible and kept centerd, so no axle is overloaded and the vehicle stays balanced from side to side.
-
45. You are about to back across a quiet street into a driveway. Which of these is good practice before you start to move?
Show answer
Answer B: Turn on the four-way flashers and sound the horn to alert anyone nearby
Warning other road users and pedestrians before a reverse maneuver gives them the chance to stop or move clear before the vehicle starts back.
-
46. A vehicle carries placards on its front, rear and both sides. What is the main purpose of those placards?
Show answer
Answer C: To tell emergency responders and other people what hazard the cargo presents
Placards warn everyone around the vehicle, especially emergency responders, about the kind of hazard the cargo presents.
-
47. You are driving past a park where children are playing close to the curb. What is the correct assumption?
Show answer
Answer A: A child may run into the street without looking
Children act on impulse and do not judge traffic well, so a driver has to expect one to enter the road and slow down in advance.
-
48. Why should a large vehicle be accelerated smoothly and gradually?
Show answer
Answer A: Rough acceleration can damage the drivetrain and, on a combination, the coupling
Jerky throttle inputs put shock loads through the driveline and the coupling, which causes mechanical damage over time.
-
49. What must the driver check about the seat belt during the inspection?
Show answer
Answer A: That it is securely mounted, adjusts properly and is not ripped or frayed
A belt only restrains the driver if its anchorage is sound and the webbing is intact, so mounting and condition are both checked.
-
50. You are entering a freeway from a short ramp with a fully loaded trailer. What should you do?
Show answer
Answer A: Begin building speed early and wait for a large gap
A loaded vehicle accelerates slowly, so it needs both a running start and a much larger gap than a car would use.